clutch Archives - Antique Tractor Blog Skip to main content

Replace your worn pressure plate.

IHS1234Now available and offered at a considerable savings is our IHS1234 clutch pressure plate for the International Harvester Cub 154 LoBoy, 185. This plate is superior to the original as it is made with ductile iron and not cast iron, increasing the tensile strength by over 100% and more importantly allowing for a significant yield strength. In addition ductile iron is more flexible and elastic. Order today!

Weekly Featured Products

IHS852 International Tilt Steering Wheel Cap

Fits International: FITS THE FOLLOWING WITH TILT WHEEL: 706, 756, 766, 806, 826, 856, 966, 1026, 1066, 1206, 1256, 1456, 1466, 1468, 1566, 1568, 2706, 2806

Replaces: 400220R1

————————————————————————-

IHS980 International Fuel Gauge w/ Sending Unit

Fits John Deere: 620, 630, 720, 730 GAS OR DSL WITH 12 Volt Electric Start

Replaces: Gauge: AF2721R & AR88048, SENDING UNIT: AF2173R

How do I test a fuel gauge?

————————————————————————-

ABC570 Economy Muffler Clamp

Fits Allis Chalmers, Avery, Case, Cockshutt, Ford, International, John Deere, Massey Ferguson, Massey Harris, Minneapolis Moline & Oliver: Models using 1-5/8" clamp

  • Ford:  — USE W/ FDS124, FDS121 (1 END ONLY)
  • Oliver — USE W/ OLS091
  • Dimensions: 1-5/8"

————————————————————————-

DEC454 Oliver Shield Decal

  • Fits Oliver: TRACTORS & EQUIPMENT
  • Dimensions & Notes: RED — 3"

 

————————————————————————-

DEC464 Case Eagle Decal

  • Fits Case: Tractors & Equipment
  • Dimensions: 6" Tall

 

 

————————————————————————-

FDS493 Ford Select-O-Speed Clutch Torque Limiter Disc

  • Fits Following Fords w/Select-O-Speed Transmission, 1959-1964: 611, 671, 681, 771, 811, 871, 881, 971, 981, 1811, 1871, 1881, 2000 (4 cyl), 2111, 4000 (4 cyl), 4121, 6000 (1961 & UP)

  • Dimensions: 7-1/4" O.D. 20 SPLINE — 1.080 SPLINE I.D.
  • Replaces: 313875, 313966, C0NN7A539B, C3NN7A539A & E8NN7A539AA

————————————————————————-

ACS357 Oil Pan Gasket

  • Fits Allis Chalmers: G & others with N62 Continental Engine
  • Fits Massey Harris: Pony & others with N62 Continental Engines
  • Replaces: Allis Chalmers: 800286
  • Replaces: Massey Harris: 1500077M1

————————————————————————-

IHS018 Back in Stock! Lower Radiator Housing

  • Fits International: CUB & CUB LOBOY
  • Replaces: International 350886R11

    ————————————————————————-

    JDS778 Fuel Gauge with Sending Unit

    • Fits John Deere: 620, 630, 720, 730 GAS OR DSL WITH 12 VOLT ELECTRIC START
    • Replaces: Gauge: AF2721R & AR88048 — Sending Unit: AF2173R
    • How do I test a fuel gauge?

    ————————————————————————-

  • Weekly Featured Products

    JDS592 Carburetor Float (Marvel Schebler) — Fits JD A, B, D, G with listed carburetors.

    Fits John Deere: Early A (up to SN 583999), B, D, G, GP

    Fits the listed Marvel Schebler carburetors:

    Carb MFG: DLTX5, DLTX6, DLTX8, DLTX10, DLTX11, DLTX12, DLTX13, DLTX15, DLTX16, DLTX17, DLTX18, DLTX19, DLTX24, DLTX31, DLTX33, DLTX34, DLTX38, DLTX39, DLTX41, DLTX51, DLTX53, DLTX63, DLTX107U, DLTX108U

    Notes: MAKE SURE THAT YOUR CARBURETOR MANUFACTURER NUMBER IS IN THE LIST THIS FITS!!!!!

    Replaces: AR10066R, MARVEL SCHEBLER # 30-635

    Can't find your carburetor manufacturer number? Click Here for helpful diagrams! How do I test my carb float? Also, need tips for rebuilding? Check out Jr's tips here!

    ———————————————————————–

    IHS070 REVERSE DRIVEN GEAR

    Fits International: 706, 756, 766, 786, 806, 826, 856, 886, 966, 986, 1066, 1086, 1206, 1256, 1456, 1466, 1468, 1486

    Dimensions: 35 teeth

    Notes: Made heavier & wider like old-style gear

    Replaces: IH: 380288R1, 138764C1

    ————————————————————————-

    JDS959 540 RPM PTO DRIVE GEAR

    Fits John Deere: 2840, 3020 (SN 123000 & UP), 4000, 4020 (SN 201000 & UP), 4030, 4040, 4050, 4055 quad & power steering, 4230, 4240, 4250, 4255 quad & power steering, 4320 syncro, 4430, 4440 power steering or quad, 4450 power steering or quad, 4455 power steering or quad

    Dimensions: 31 TEETH

    Replaces: R42014

    ————————————————————————-

    JDS1076 PTO Clutch Plate (with facing)

    Fits John Deere: 50 (SN: 5032350 & UP), 60 (SN: 6060700 & UP), 70 (SN: 7039400 & UP), 80, 520, 530, 620, 630, 720, 730, 820, 830

    Notes: 2 used per tractor — Sold Individually

    Replaces: AR1293R, RE29794

    ————————————————————————-

    JDS1078 PTO Brake Plate (with facing)

    Fits John Deere: 80, 620, 530, 720, 730, 820, 830

    Notes: 1 Used per tractor

    Replacement: AF2768R, RE20727

    ————————————————————————-

    JDS1080 PTO Clutch Drive Disc

    Fits John Deere: 80, 820, 830

    Notes: 12 Used per Tractor — Sold Individually

    Replaces: R1902R

    ————————————————————————-

    IHS901 Crankshaft Gear

    Fits International: GAS / LP: A, AV, B, BN, C, SUPER A, SUPER AV, SUPER A1, SUPER AV1, 100, 130, 140, 200, 230, 240, 330, 340, 404, 424, 444, 504, 2404, 2424, 2444, 2504, 3444, 3514, T5, T340, 500 CRAWLERS

  • Dimensions: 33 TEETH
  • Replaces: 46870DA

    ————————————————————————-

    JDS1074 PTO Clutch Drive Disc

    Fits John Deere: 50 (6 — USED UP TO SN: 5016358; 7 — USED SN: 5016359 & UP), 60 (6 — USED UP TO SN: 6031044; 7 — USED SN: 6031045 & UP), 70 (8 — USED UP TO SN: 7008972; 9 — USED SN: 7008973 – 7039399; 8 — USED SN: 7039400 & UP), 520 (7 — USED), 530 (7 — USED), 620 (9 — USED), 630 (9 — USED), 720 (12 — USED), 730 (12 — USED)

    Notes: SOLD INDIVIDUALLY

    Replaces: A5145R

    ————————————————————————-

    ABC558 Steering Worm Shaft Bearing

    Fits Allis Chalmers: Rear wormshaft bearing, manual steering only D14, D15, D17, D19 1 Used per tractor

    Cockshutt: COOP; E2, E4, E5 — Cockshutt; 20, 35, 40, 50, 540, Golden Arrow, Golden Eagle 2 Used per Tractor- Sold Individually

    John Deere: B, BN, BNH, BW, BWH; (SN 60000 & UP) 2 Used per Tractor – Sold Individually

    Oliver: 70 Industrial Only (SN 400635 & UP)

    Dimensions: I.D. = 1.311, O.D. = 1.938, .506 wide

    Replaces: AC; TG8538A, TG8538C, 70228150 – COOP Cockshutt; TG8538 – JD; JD7396 – Oliver; F6769

  • Weekly Featured Products

    Every week Steiner Tractor Parts features several products on our home page. The featured products could be new products recently added to our line, product that has been out of stock for some time and is back on the shelves, or a 'product pick' that either Danny or Jenny feel should be brought to the attention of our customers. To view our featured products go to our home page at www.steinertractor.com or check here for our weekly updates.

    IHS958  IHS958 NEW International 9" Clutch Kit Fits: A, AV, Super A, Super AV, Super A1, Super AV1, B, BN, C, Super C, 100, 130, 140, 200, 230, 240, 404, 2404 — Older models may require the purchase of a new style throw out bearing sleeve if the tractor is equipped with  a carbon (non-turning) throwout bearing.  New style throwout bearing sleeves are available by special order. Replaces: Clutch: 56631DB, 375695R92 — Throwout Bearing: 18567D, 361292R91 — Pressplate: 375493R91, 353242R92, 384383R91, 375547R91 — Pilot Bushing: 43291D, 364527R91,

    9" diameter, 3 lever, 6 spring, pressure plate with .500 wide at the fingers —  Includes new pressure plate, new fiber spring loaded clutch disc, new press onthrowout bearing & new pilot bushing.

    MFS165  Massey Ferguson Lower Stainless Grille Chin Trim  Fits: MF50, 65, 95 (UP TO SN 15601101),MFS165 Replaces: 182384MI + 182445MI (FASTENER) 7  3/4" O.A. Length — Includes 2 Trim Fasteners

    MFS161 MFS161 Grille Center Bar Trim with Attaching Hardware Fits: MF50, 65, Replaces: 184804M1, Stainless Steel, 1 3/8" Wide 19" Overall Length

    New John Deere Clutch Lever Pivot Bushing and Brake or Clutch Pedal Bushings!

    JDS891 We’ve recently added a bushing that can be used on the Clutch Lever Pivot, or the Brake or the Clutch Pedal.  Our stock number for this new bushing is JDS891.  This is used as a Clutch Lever Pivot Bushing on the following John Deere models:   A, AN, AW, ANH, AWH, D, G, GH, GM, GW, W, R, 80, 820, 830, 60, 70, 70D, 520, 530, 620, 630, 720, 730, 720D, 730D.  This is used as a brake or clutch pedal bushing on the following John Deere Models:   4030, 4230, 4430, 4040, 4230, 4240, 4430, 4440, 4050, 4055, 4255, 4455, 4230, 4555, 4755, 4955, 4630, 4640, 4650, 4840, 4840, 4850, 8020, 8430, 8630, 8440, 8640, 8450, 8650, 8560, 8850. We sell this bushing for $7.50 each.  JDS891 replaces John Deere number A1197R and R51192.  You can order easily order these through our website!  Also, if you are ordering this bushing, you may be interested in our Clutch Lever Pivot Bolt for John Deere tractors.  Check out stock number JDS887!

    JDS893

    We also added JDS893, the clutch lever pivot bushing for John Deere model B and 50.  This same part is used as a Brake Pedal bushing on the following models:  820 3 CYL, 830 3 CYL, 1020, 1520, 1530, 2020, 2030, 2155, 2240, 2350, 2355, 2440, 2510, 2520, 2550, 2555, 2630, 2640, 2750, 2755, 2840, 2855, 2940, 2950, 3010, 3020, 3150, 4000, 4010, 4020, 4320, 4520, 4620, 5010, 5020, 6030, 7020, 7520, INDUSTRIAL 210C, INDUSTRIAL 300B.  This can also be used as a starter lever bushing 80, 820, 830 2 CYL. JDS893 has a current price of $7.50.  This bushing replaces John Deere number B177R. Also, if you are ordering this bushing, you may be interested in our Clutch Lever Pivot Bolt for John Deere tractors.  Check out stock number JDS881!